The end ofcup sweat.
No Sweat® is engineered to reduce exterior condensation on cold drinkware, helping keep hands, desks, counters and cupholders drier.
Developed to reduce exterior condensation on cold drinkware.
- Engineered to reduce condensation
- Drier hands
- Cleaner desks
- Clear water-based spray
- Made for cold drinks
- 4 oz, 16 oz and 1 gallon
Your drink should be cold.Your desk shouldn't be wet.
Wet hands
Every sip starts with a slippery grip.
Soaked cupholders and desks
Condensation runs down the cup and soaks whatever it sits on.
Water rings and cleanup
Rings on wood, puddles on counters, and a towel every time.
We test in the open.
Prototype testing is under way. Each test is published with its conditions, formula revision and status, so you can see what was tested and how. New results appear on the Testing page as they are verified.
See testing statusEvery test record includes
- Cup material and surface preparation
- Formula revision, coats and cure time
- Room temperature and humidity
- Drink and ice temperature
- Duration
- Control and treated results
- Photos and video from the same session
Three steps. Outside of the cup only.
- 1
Prep
Clean the outside of the cup with isopropyl alcohol and let it dry.
- 2
Apply
Shake well. In a well-ventilated area, spray from 6 to 10 inches away in light, even coats.
- 3
Cure
Let it dry for 5 minutes, then add a second thin coat for best results.
No Sweat® forms a thin, clear layer on the outside of the cup. It is engineered to change how heat and moisture behave at that surface.
Apply to outside surfaces only, never to the inside of a cup or any surface that touches food or drink. Safety and directions
Pick your size.
Directions and the Safety Data Sheet are on every product page.
Buying for a café, bar or event? Send a commercial inquiry.
Why No Sweat®
Less condensation
Engineered to reduce the water that collects on the outside of a cold cup.
Cleaner surfaces
Helps keep water off desks, counters and cupholders.
Clear application
A clear, water-based spray that goes on the outside of the cup.
Built for cold-drink environments
Sized from a personal bottle to a commercial gallon for cafés, bars and events.
Made for cold drinkware.
No Sweat® goes on the outside of the cup. Drinkware is where our testing is focused.
Disposable plastic cups
Iced coffee, tea and soda cups.
Reusable tumblers
Insulated and uninsulated tumblers you carry all day.
Glassware
Cold-drink glasses at home and behind the bar.
Stainless drinkware
Bottles and mugs in brushed or coated steel.
Beverage-service equipment
Pitchers, shakers and server-side drinkware.
Mirrors and bathroom glass
Under evaluation. Not yet tested.
Windshields and everyday glass
Under evaluation. Not yet tested.
Safety and response gear
Under evaluation. Not yet tested.
Condensation is physics.So is the solution.
Condensation forms when a surface is colder than the dew point of the air around it. A cold drink chills the outside of its cup below that point, so water vapor in the room turns to liquid on the cup.
No Sweat® is engineered to reduce that effect at the surface. How well it works depends on temperature and humidity, which is why we publish our test conditions.
Try your room
Dew point
65°F
Any surface colder than this collects water.
An iced drink (about 38°F) is 27°F below the dew point in this room, so water vapor will condense on the cup.
Built for morethan one cup.
Cafés, restaurants, bars and event teams pour cold drinks all day. Tell us about your volume and we'll follow up about commercial sizes and pricing.
Commercial & wholesaleWhat is No Sweat®?
No Sweat® is a clear, water-based spray coating that you apply to the outside of cold drinkware. It is engineered to reduce exterior condensation, helping keep hands, desks, counters and cupholders drier.
Does it completely stop condensation?
No. How much water collects on a cup depends on temperature and humidity, and condensation can still form under some conditions. No Sweat® is engineered to reduce it, not to guarantee a perfectly dry cup.
We publish test conditions and results on the Testing page so you can judge for yourself.
How do I apply it?
- Clean the outside of the cup with isopropyl alcohol and let it dry.
- Shake the bottle well.
- In a well-ventilated area, spray from 6 to 10 inches away in light, even coats.
- Let it dry for 5 minutes.
- Apply a second thin coat for best results.
Where should I spray it, and where should I not?
Spray only the outside of the cup. Do not apply No Sweat® to the inside of a cup or to any surface that touches food or drink. It is not for ingestion.
Use it in a well-ventilated area, avoid breathing the spray mist, and wear eye protection.
Which cups and surfaces is it for?
No Sweat® is designed for the outside of cold drinkware: disposable plastic cups, reusable tumblers, glassware and stainless drinkware.
We are evaluating other surfaces. We will only list a surface as supported once it has been tested.
How should I store it?
Keep tightly closed at 41–86°F (5–30°C). Keep from freezing and out of direct sunlight. Shelf life is about 24 months.
What is the testing status?
No Sweat® is in prototype testing. Each test is published with its conditions, formula revision and status: prototype, development test, verified or superseded.
Questions? Talk to us.
Orders, the product, safety information or anything else. Send a message and we’ll reply by email.
- Product information and emergencies
- 207-745-7575
- PO Box 52, Detroit, ME 04929
